Vertiv logo

Electrical Engineer

Vertiv

On-site
Shenzhen, China
Full-time
Mid Level
3+ yrs
Salary not listedPosted 5h ago

Real job — pulled straight from Vertiv’s careers page · Verified November 16, 2026 · No reposts.

Job description

Vertiv is hiring a Electrical Engineer — a full-time, based in Shenzhen, China role. Apply directly on Vertiv's careers page below.

TM-Electrical Engineer(Global)-Shenzhen

Location: Shenzhen-xili, China

Key Responsibilities
  1. Lead electrical hardware design of DX cooling units, including power distribution circuit, compressor/EEV/fan drive control, sensor sampling, protection circuit, wiring diagram, terminal definition and cabinet layout.
  2. Define BOM for electrical components: VFD, controller, EEV driver, current/voltage/temperature/pressure sensors, contactors, circuit breakers, relays and power supplies; conduct component selection, evaluation and single-source risk management.
  3. Develop electrical schematics, wiring drawings, panel layout, cable routing specification and test procedure; manage drawing release, revision and technical document control.
  4. Conduct EMC, electrical safety and reliability assessment; organize related verification tests (surge, ESD, conducted/radiated emission, insulation, withstand voltage, over-current/over-temperature protection).
  5. Support control logic integration with thermal system: compressor capacity regulation, EEV superheat control, fan speed modulation, alarm interlock, fault diagnosis and protection logic matching for DX refrigeration cycle.
  6. Drive DFM review for electrical design, work with manufacturing and supply chain to optimize wiring harness, panel assembly and testability; support cost optimization of electrical bill of material.
  7. Support prototype, pilot run and mass production ramp-up; troubleshoot electrical and control issues including communication failure, sensor drift, drive abnormal trip, protection misfire and wiring interference during NPI and volume production.
  8. Resolve field quality escalations related to electrical hardware, drive faults, signal noise and protection failures; conduct root cause analysis and roll out corrective & preventive actions.
  9. Track relevant industry standards, safety certifications and new electrical components for cooling equipment; complete benchmarking and technical pre-research for next-gen DX control platforms.
  10. Align with thermal, mechanical and product teams to translate product requirements into electrical design, balancing safety, reliability, performance, cost and serviceability.
Required Qualifications & Skills
  1. Bachelor’s degree or above in Electrical Engineering, Automation, Control Science & Engineering, Refrigeration & HVAC or related discipline.
  2. 3+ years electrical hardware design experience for HVAC / refrigeration equipment; solid experience in refrigeration unit power and control circuit design.
  3. Proficient in E-CAD tools (EPLAN preferred); familiar with electrical drawing standards, low-voltage distribution, wiring harness design and component specification.
  4. Hands-on experience with EMC and electrical safety test requirements; understand common protection mechanisms for compressor, EEV and fan drive systems.
  5. Basic understanding of DX refrigeration cycle, superheat control and typical operating faults of direct expansion cooling systems.
  6. Familiar with reliability test methodology for cooling products; able to conduct electrical fault analysis and design improvement.
  7. Strong systematic thinking, good cross-team communication; capable of managing multiple tasks under tight NPI schedules.
  8. Good English reading and writing skills for technical documents and global cross-team communication.
Preferred Qualifications
  • Experience on data center mission-critical cooling products (DX CRAC, in-row cooler)
  • Familiar with Modbus / BACnet communication and building management system integration
  • Practical experience with variable frequency drive commissioning and EEV control tuning
  • Experience supporting NPI from concept to mass production
  • Knowledge of IEC, UL and other global electrical safety standards for cooling equipment

 

As a DX Electrical & Controls Engineer, you own the electrical hardware design, control system implementation, EMC/safety validation, BOM development and technical issue resolution for direct expansion cooling products for mission-critical data center thermal systems. You collaborate with thermal, mechanical, product, manufacturing and quality teams to deliver safe, reliable, compliant and cost-effective DX cooling units from prototype to mass production.

Get Electrical Engineer jobs like this→

New roles from thousands of companies land hourly, straight from their careers pages. Get the freshest matches by email so you never miss one.

Email me new jobs
CRB Group logo

Electrical Engineer

Raleigh, NC
✓ From careers page· 21h ago
CRB Group logo

Electrical Engineer

Jacksonville, FL
✓ From careers page· 21h ago
CRB Group logo

Electrical Engineer

Atlanta, GA
✓ From careers page· 21h ago
CRB Group logo

Electrical Engineer

Emeryville, CA
✓ From careers page· 21h ago

Frequently asked questions

What is the seniority level for Electrical Engineer at Vertiv?

Electrical Engineer at Vertiv is a Mid Level level position.

How do I apply for Electrical Engineer at Vertiv?

You can view the full description and apply for Electrical Engineer at Vertiv on EchoJobs: https://echojobs.io/job/vertiv-tm-electrical-engineer-global-shenzhen-oerz7.